When your siding fails, it doesn't fail quietly. Moisture gets into sheathing, energy costs climb, and the interior damage that follows is always more expensive than the exterior repair that would have stopped it. Forge Siding puts licensed, manufacturer-certified crews on your property — crews who diagnose the actual problem, price it in writing, and fix it once.

Forge Siding has been delivering Fiber Cement Siding across Colorado, CO for over fifteen years. Our lead installers hold manufacturer certifications on every cladding system we install — fiber cement, vinyl, engineered wood, steel — and the same crew that estimates your project executes it. We don't sub out the technical work.
We work across the full project range: single-panel storm repairs, complete whole-home re-siding, new construction cladding alongside general contractors, and commercial multi-family projects for property managers who need consistent quality and documentation across multiple buildings.
We've completed projects in every climate zone Colorado, CO presents — high-humidity coastal exposures, high-altitude freeze-thaw cycling, urban heat island conditions. That geographic breadth translates to practical knowledge about product selection and installation specification that out-of-market contractors working from a generic spec sheet simply don't have.

Most siding failures start as small, quiet problems. Catching them before they reach your wall cavity changes the repair scope dramatically — and the cost even more so.
Any crack through the panel face is an active moisture entry point. Window corners and butt joints are the highest-risk locations — and the easiest to overlook until they've allowed a full season of water infiltration.
Drywall staining, soft spots when you press near exterior walls, or a persistent musty odor in exterior-adjacent rooms are downstream indicators. The sheathing has usually been wet for weeks before these symptoms appear.
Warped wood siding typically means unpainted back faces — differential expansion between the painted front and the raw back causes curvature that worsens with every moisture cycle.
Exterior paint failing within two to four years of application on wood or fiber cement is almost always a back-priming failure — moisture migrates through the panel from behind and pushes the front paint off. Re-painting without addressing this repeats the cycle.
Dark streaking from nailhead locations on vinyl or fiber cement means non-galvanized fasteners are corroding. As the fastener degrades, its holding strength decreases — a panel secured by a corroded nail is a panel waiting to separate in a windstorm.
A compromised siding system — failed housewrap, open panel joints, missed penetration caulk — creates air infiltration that significantly increases HVAC load. If your heating or cooling costs have climbed without obvious explanation, the building envelope is a legitimate first suspect.
Every service below is performed by our own licensed crew — not passed to a subcontractor network we don't control. We carry the manufacturer certifications, the diagnostic tools, and the installation experience for every scope we quote.
Installation quality is the variable that separates a 15-year siding job from a 35-year one. The correct expansion gap for your CO climate, the proper back-priming of fiber cement field cuts, the housewrap integration at rough openings — these details determine long-term performance and they aren't optional on our projects.
For full replacement projects, our tear-off process includes substrate inspection with a calibrated moisture meter on every exposed wall section. Sheathing damage found during demo is documented with photos and priced in a written change order before any additional work proceeds — not discovered on the final invoice.

Siding repair in Colorado, CO covers a range that extends well beyond swapping a cracked panel: hail and wind damage after storms, impact holes from debris or vehicle contact, failed caulk joints at penetrations allowing water infiltration, loose or blown-off panels, and moisture-infiltrated substrate that requires sheathing repair before new cladding can go on. Our Colorado, CO repair crews carry common panel stock, a moisture meter, and caulk probe tools on every service truck — so assessment and often same-day repair happen in a single visit.
For insurance-related damage, we produce a panel-level photo documentation package — close-range images by elevation, written damage scope, and material specifications formatted for adjuster review. After the initial adjuster estimate comes in lower than the actual scope, our documentation has supported successful appeals on a significant number of Colorado, CO claims. That documentation service is included in every storm inspection at no additional charge.

Each cladding material has distinct installation requirements that determine whether it performs for 10 years or 40. Our Colorado, CO crews hold certifications specific to the products they install — not one generic approach applied to every material. Fiber cement installation requires back-priming at every field cut, hot-dipped galvanized or stainless fasteners, documented fastener schedules per the manufacturer guide, and silica dust controls during cutting operations. Vinyl installation requires expansion gaps calibrated to the local temperature range in CO. Wood siding requires moisture content verification at delivery, species-appropriate nailing patterns, and end-grain sealing at every butt joint. We address each of these requirements as non-negotiable installation practice.
Beyond installation, we perform professional siding inspections — pre-purchase assessments for buyers, post-storm condition reports for insurance claims, and annual maintenance inspections for property owners who want to catch caulk failures and minor fastener movement before they become moisture damage. These inspections use calibrated pin-type and non-invasive capacitance meters for moisture assessment — tools a general home inspector doesn't carry. The written report you receive ranks deficiencies by priority and includes rough cost ranges for every item.

Vinyl soffit and fascia wrap, HardieTrim boards, aluminum-capped fascia, and fiber cement trim boards are all within our scope. On replacement projects, we replace trim components that are damaged or compromised regardless of the primary panel material — because leaving failing trim behind a new siding installation creates the exact moisture entry point the new siding was supposed to eliminate.

A professional siding inspection before buying or selling a Colorado, CO property gives you panel-level condition documentation that general home inspectors don't produce. We assess fastener schedules, test caulk integrity at penetrations, probe sheathing moisture with calibrated meters, and deliver a priority-ranked written report with photo documentation and rough repair cost ranges. Pre-purchase inspections have identified sheathing moisture on properties where the general inspection report said the siding was "in acceptable condition."

Property managers and HOA boards working with us get a dedicated project point of contact, building-by-building scheduling documentation, and a close-out package — permit records, warranty registrations, per-building photos — formatted for board records and institutional property management systems.

These aren't aspirational claims. They're the operational standards our Colorado, CO clients reference when they send us referrals. Each one is documented and verifiable.
Lump-sum estimates are the contractor's tool. Line-item estimates are the client's. We provide the latter on every project, from a single-panel repair to a full commercial re-siding contract.
We don't schedule jobs we can't start within a reasonable window. Current backlog means a delay? We tell you upfront with realistic dates, not optimistic ones designed to close the sale.
An unlicensed contractor on your property creates liability exposure for you personally. License verification before signing eliminates the most common contractor fraud scenario in the Colorado, CO market.
We also deliver a complete close-out package: permit records, manufacturer warranty registrations, and post-project photos organized by elevation. That file is useful for insurance renewals, property sales, and HOA records long after the project ends.
Staging tarps protect landscaping and driveways before demo starts. We sweep for fasteners every afternoon before the crew leaves. Debris is hauled off-site rather than sitting in a roll-off on your driveway for three weeks after the project ends.
You don't have to call us to find out where your project stands. We tell you, every day, in writing.
The same documented process governs every project we take in Colorado, CO. No mystery, no moving goalposts — you know what's happening at every stage.
You get a real conversation with a dispatcher who knows the product — not a scheduling app that drops your request into a queue. The site assessment is diagnostic, not just a measuring visit.
Delivered within 24 hours of the site visit. Every component — panels, trim, housewrap, fasteners, labor, permit fee — listed separately. We bring material samples to the estimate meeting and walk through the product trade-offs relevant to your Colorado, CO property.
Material is ordered against the confirmed schedule. We don't stage material before it's needed and we don't start jobs with missing material. Your crew arrives on day one with everything they need.
Morning update from the lead installer confirming the day's scope. Afternoon update reporting what was completed. Unexpected substrate conditions documented same-day with photos and a written change order — never added to the invoice without prior approval.
We walk every elevation with you at project completion. Every scope item verified complete. If anything isn't right, we note it and fix it before considering the project closed. Final payment collected after the walkthrough sign-off — not before.
The moisture meter reading at the estimate visit — before we'd agreed to anything — flagged elevated sheathing moisture behind our north wall. That diagnostic step upfront told me immediately what kind of contractor I was dealing with. The rest of the project matched that first impression exactly.
Overnight storm, eight panels blown off the north wall. Called at 5:45 AM. Someone actually answered. Crew on-site by 9:30, matching panels installed, wall complete before noon. I'll never use another contractor for anything on this house's exterior.
Pre-purchase inspection on a property we were evaluating found sheathing moisture on two elevations the general home inspector had completely missed. Used the written report to negotiate a $12,000 seller credit. The inspection paid for itself about 40 times over.
They found rotted sheathing on the west wall during tear-off. Called me within the hour, showed me the photos, issued a change order before doing anything. That's the process working exactly as it should — and it's shockingly rare in my experience with contractors.
The daily morning and afternoon updates from the lead installer were something I hadn't expected. I always knew exactly where the project stood. When the permit inspection happened, I heard about it the same day it passed.
Three bids — two lump sums and one line-item breakdown from Forge Siding. The line-item document made comparison possible in a way the other two bids didn't. When the choice becomes that clear, the decision is easy.
Forge Siding provides residential and commercial Fiber Cement Siding across the full Colorado, CO service area from our locally based dispatch team. We're familiar with local building codes, permit requirements, and contractor licensing standards throughout CO — no learning curve on your project, no out-of-area crew navigating unfamiliar inspectors and building departments for the first time.