When your siding fails, it doesn't fail quietly. Moisture gets into sheathing, energy costs climb, and the interior damage that follows is always more expensive than the exterior repair that would have stopped it. Forge Siding puts licensed, manufacturer-certified crews on your Reading property — crews who diagnose the actual problem, price it in writing, and fix it once.

Forge Siding has been delivering Siding across Reading, PA for over fifteen years. Our lead installers hold manufacturer certifications on every cladding system we install — fiber cement, vinyl, engineered wood, steel — and the same crew that estimates your project executes it. We don't sub out the technical work.
We work across the full project range: single-panel storm repairs, complete whole-home re-siding, new construction cladding alongside general contractors, and commercial multi-family projects for property managers who need consistent quality and documentation across multiple buildings.
We've completed projects in every climate zone Reading, PA presents — high-humidity coastal exposures, high-altitude freeze-thaw cycling, urban heat island conditions. That geographic breadth translates to practical knowledge about product selection and installation specification that out-of-market contractors working from a generic spec sheet simply don't have.

Most siding failures start as small, quiet problems. Catching them before they reach your wall cavity changes the repair scope dramatically — and the cost even more so.
Any crack through the panel face is an active moisture entry point. Window corners and butt joints are the highest-risk locations — and the easiest to overlook until they've allowed a full season of water infiltration.
Interior moisture near windows is frequently misdiagnosed as a window problem. Failed flashing or caulk at the rough opening — a siding-system issue — is the actual source in the majority of cases we diagnose in PA.
Warped wood siding typically means unpainted back faces — differential expansion between the painted front and the raw back causes curvature that worsens with every moisture cycle.
Exterior paint failing within two to four years of application on wood or fiber cement is almost always a back-priming failure — moisture migrates through the panel from behind and pushes the front paint off. Re-painting without addressing this repeats the cycle.
Fastener specification is the most commonly skipped installation requirement. We've documented hundreds of Reading, PA properties where the original installer used bright nails on fiber cement, voiding the material warranty before the first winter.
Wall air leakage through siding failures can account for 10–20% of annual HVAC energy consumption. Addressing the envelope often produces measurable utility savings alongside the repair value.
Every service below is performed by our own licensed crew — not passed to a subcontractor network we don't control. We carry the manufacturer certifications, the diagnostic tools, and the installation experience for every scope we quote.
New siding installation covers the complete scope: housewrap, flashing at all penetrations, panel installation per manufacturer specification, and finishing trim at corners, windows, doors, and the roofline. We work on new construction alongside general contractors and handle full tear-off replacements on existing Reading, PA homes and commercial properties. Our crews are certified on vinyl, fiber cement, engineered wood, and steel panel systems — with the documentation to keep every material warranty in force.
For full replacement projects, our tear-off process includes substrate inspection with a calibrated moisture meter on every exposed wall section. Sheathing damage found during demo is documented with photos and priced in a written change order before any additional work proceeds — not discovered on the final invoice.

Siding repair in Reading, PA covers a range that extends well beyond swapping a cracked panel: hail and wind damage after storms, impact holes from debris or vehicle contact, failed caulk joints at penetrations allowing water infiltration, loose or blown-off panels, and moisture-infiltrated substrate that requires sheathing repair before new cladding can go on. Our Reading, PA repair crews carry common panel stock, a moisture meter, and caulk probe tools on every service truck — so assessment and often same-day repair happen in a single visit.
Emergency dispatch for genuine siding emergencies — missing panels with rain incoming, active moisture entry into a wall cavity, structural damage — is available around the clock. A live dispatcher answers, not an answering queue. We triage by exposure severity and send a crew based on actual risk.

Manufacturer certification matters for one concrete reason: it's the difference between a material warranty that's in force and one that's already voided before the project is complete. Our James Hardie Preferred Contractor status, for example, means the 30-year material warranty on every fiber cement project we complete is fully registered in the client's name at project close.
Beyond installation, we perform professional siding inspections — pre-purchase assessments for buyers, post-storm condition reports for insurance claims, and annual maintenance inspections for property owners who want to catch caulk failures and minor fastener movement before they become moisture damage. These inspections use calibrated pin-type and non-invasive capacitance meters for moisture assessment — tools a general home inspector doesn't carry. The written report you receive ranks deficiencies by priority and includes rough cost ranges for every item.

Vinyl soffit and fascia wrap, HardieTrim boards, aluminum-capped fascia, and fiber cement trim boards are all within our scope. On replacement projects, we replace trim components that are damaged or compromised regardless of the primary panel material — because leaving failing trim behind a new siding installation creates the exact moisture entry point the new siding was supposed to eliminate.

A professional siding inspection before buying or selling a Reading, PA property gives you panel-level condition documentation that general home inspectors don't produce. We assess fastener schedules, test caulk integrity at penetrations, probe sheathing moisture with calibrated meters, and deliver a priority-ranked written report with photo documentation and rough repair cost ranges. Pre-purchase inspections have identified sheathing moisture on properties where the general inspection report said the siding was "in acceptable condition."

Property managers and HOA boards working with us get a dedicated project point of contact, building-by-building scheduling documentation, and a close-out package — permit records, warranty registrations, per-building photos — formatted for board records and institutional property management systems.

These aren't aspirational claims. They're the operational standards our Reading, PA clients reference when they send us referrals. Each one is documented and verifiable.
Materials, labor, permit fees, and disposal listed separately on every estimate. You know exactly what you're paying for before signing. The estimate becomes the contract, and the final invoice reflects it — no lump-sum numbers we can pad quietly.
We don't schedule jobs we can't start within a reasonable window. Current backlog means a delay? We tell you upfront with realistic dates, not optimistic ones designed to close the sale.
An unlicensed contractor on your property creates liability exposure for you personally. License verification before signing eliminates the most common contractor fraud scenario in the Reading, PA market.
We also deliver a complete close-out package: permit records, manufacturer warranty registrations, and post-project photos organized by elevation. That file is useful for insurance renewals, property sales, and HOA records long after the project ends.
Staging tarps protect landscaping and driveways before demo starts. We sweep for fasteners every afternoon before the crew leaves. Debris is hauled off-site rather than sitting in a roll-off on your driveway for three weeks after the project ends.
The lead installer contacts you each morning to confirm the day's scope and each afternoon to report what was completed. If the project uncovers unexpected conditions — the sheathing damage that shows up during tear-off — you hear about it same-day with photos and a written change order, before we touch anything additional.
The same documented process governs every project we take in Reading, PA. No mystery, no moving goalposts — you know what's happening at every stage.
Our Reading, PA dispatch team takes your call and books a free on-site assessment within 24–48 hours. We arrive with measuring tools and a moisture meter, document all wall planes and existing substrate conditions, and identify any issues before quoting.
The estimate is a document, not a handshake. It becomes the contract, and every line item is visible before you sign. No lump-sum number to parse after the fact.
Material is ordered against the confirmed schedule. We don't stage material before it's needed and we don't start jobs with missing material. Your crew arrives on day one with everything they need.
We don't consider a surprise to be discovered after the project ends. If we find something during the project, you know about it before we act on it.
Close-out package delivered: permit records, manufacturer warranty registrations in your name, post-project photos by elevation, and our signed workmanship warranty document. Everything in one organized file.
Full replacement, line-item estimate, project finished on schedule, and a close-out package with every warranty document organized before I signed off on final payment. This is what a professional siding project actually looks like.
Overnight storm, eight panels blown off the north wall. Called at 5:45 AM. Someone actually answered. Crew on-site by 9:30, matching panels installed, wall complete before noon. I'll never use another contractor for anything on this house's exterior.
We manage a 34-unit townhome community. The per-building documentation, the building-by-building scheduling, the HOA board close-out package — these are things I'd been trying to get from contractors for years and never received until Forge Siding.
They found rotted sheathing on the west wall during tear-off. Called me within the hour, showed me the photos, issued a change order before doing anything. That's the process working exactly as it should — and it's shockingly rare in my experience with contractors.
The daily morning and afternoon updates from the lead installer were something I hadn't expected. I always knew exactly where the project stood. When the permit inspection happened, I heard about it the same day it passed.
Site was clean every evening — tarps on the landscaping, fasteners swept, no debris left overnight. On the last day of the project, the yard looked better than when they'd arrived. That's a detail that matters.
Forge Siding provides residential and commercial Siding across the full Reading, PA service area from our locally based Reading dispatch team. We're familiar with local building codes, permit requirements, and contractor licensing standards throughout PA — no learning curve on your project, no out-of-area crew navigating unfamiliar inspectors and building departments for the first time.
Currently active in: 19604 19601 19602 19611 19603 19612 and surrounding areas