Forge Siding delivers professional Siding across Amherst, TX with locally based crews who understand Amherst's specific climate conditions, permit requirements, and building codes. Not a franchise call center routing jobs to whoever's free — a licensed contractor with written credentials and a documented track record.

What makes our Amherst operation different isn't a slogan. It's the fact that every estimate we write is line-item detailed, every project has a named lead installer accountable for the outcome, and every completed job closes with a written workmanship warranty you can actually enforce.
Our TX operation is licensed, bonded, and insured — GL and workers' comp both current, certificates available before any project starts. Not because it's optional, but because a property owner deserves protection when they invite a crew onto their building.
We've completed projects in every climate zone Amherst, TX presents — high-humidity coastal exposures, high-altitude freeze-thaw cycling, urban heat island conditions. That geographic breadth translates to practical knowledge about product selection and installation specification that out-of-market contractors working from a generic spec sheet simply don't have.

Most siding failures start as small, quiet problems. Catching them before they reach your wall cavity changes the repair scope dramatically — and the cost even more so.
Any crack through the panel face is an active moisture entry point. Window corners and butt joints are the highest-risk locations — and the easiest to overlook until they've allowed a full season of water infiltration.
Drywall staining, soft spots when you press near exterior walls, or a persistent musty odor in exterior-adjacent rooms are downstream indicators. The sheathing has usually been wet for weeks before these symptoms appear.
Warped wood siding typically means unpainted back faces — differential expansion between the painted front and the raw back causes curvature that worsens with every moisture cycle.
On fiber cement specifically, field cuts that weren't back-primed at installation are the entry point. The paint fails at cut edges first and the pattern makes the cause obvious to anyone who's diagnosed it before.
Dark streaking from nailhead locations on vinyl or fiber cement means non-galvanized fasteners are corroding. As the fastener degrades, its holding strength decreases — a panel secured by a corroded nail is a panel waiting to separate in a windstorm.
A compromised siding system — failed housewrap, open panel joints, missed penetration caulk — creates air infiltration that significantly increases HVAC load. If your heating or cooling costs have climbed without obvious explanation, the building envelope is a legitimate first suspect.
Our Amherst, TX team handles the full spectrum of residential and commercial cladding work from single-panel storm repairs to complete building envelope re-siding on large multi-family properties.
Installation quality is the variable that separates a 15-year siding job from a 35-year one. The correct expansion gap for your TX climate, the proper back-priming of fiber cement field cuts, the housewrap integration at rough openings — these details determine long-term performance and they aren't optional on our projects.
For full replacement projects, our tear-off process includes substrate inspection with a calibrated moisture meter on every exposed wall section. Sheathing damage found during demo is documented with photos and priced in a written change order before any additional work proceeds — not discovered on the final invoice.

Siding repair in Amherst, TX covers a range that extends well beyond swapping a cracked panel: hail and wind damage after storms, impact holes from debris or vehicle contact, failed caulk joints at penetrations allowing water infiltration, loose or blown-off panels, and moisture-infiltrated substrate that requires sheathing repair before new cladding can go on. Our Amherst, TX repair crews carry common panel stock, a moisture meter, and caulk probe tools on every service truck — so assessment and often same-day repair happen in a single visit.
Emergency dispatch for genuine siding emergencies — missing panels with rain incoming, active moisture entry into a wall cavity, structural damage — is available around the clock. A live dispatcher answers, not an answering queue. We triage by exposure severity and send a crew based on actual risk.

Each cladding material has distinct installation requirements that determine whether it performs for 10 years or 40. Our Amherst, TX crews hold certifications specific to the products they install — not one generic approach applied to every material. Fiber cement installation requires back-priming at every field cut, hot-dipped galvanized or stainless fasteners, documented fastener schedules per the manufacturer guide, and silica dust controls during cutting operations. Vinyl installation requires expansion gaps calibrated to the local temperature range in TX. Wood siding requires moisture content verification at delivery, species-appropriate nailing patterns, and end-grain sealing at every butt joint. We address each of these requirements as non-negotiable installation practice.
Beyond installation, we perform professional siding inspections — pre-purchase assessments for buyers, post-storm condition reports for insurance claims, and annual maintenance inspections for property owners who want to catch caulk failures and minor fastener movement before they become moisture damage. These inspections use calibrated pin-type and non-invasive capacitance meters for moisture assessment — tools a general home inspector doesn't carry. The written report you receive ranks deficiencies by priority and includes rough cost ranges for every item.

Vinyl soffit and fascia wrap, HardieTrim boards, aluminum-capped fascia, and fiber cement trim boards are all within our scope. On replacement projects, we replace trim components that are damaged or compromised regardless of the primary panel material — because leaving failing trim behind a new siding installation creates the exact moisture entry point the new siding was supposed to eliminate.

A professional siding inspection before buying or selling a Amherst, TX property gives you panel-level condition documentation that general home inspectors don't produce. We assess fastener schedules, test caulk integrity at penetrations, probe sheathing moisture with calibrated meters, and deliver a priority-ranked written report with photo documentation and rough repair cost ranges. Pre-purchase inspections have identified sheathing moisture on properties where the general inspection report said the siding was "in acceptable condition."

Commercial siding in TX operates on different requirements than residential: higher fastener schedules for wind-load compliance, special inspection documentation in applicable jurisdictions, coordinated scheduling for occupied buildings, and standardized documentation for HOA board records and reserve fund planning. Our commercial crews are familiar with the permitting landscape in TX and have completed projects ranging from small townhome communities to larger multi-family re-siding contracts.

There are plenty of siding contractors in TX. Here's what the ones worth hiring actually do differently.
Materials, labor, permit fees, and disposal listed separately on every estimate. You know exactly what you're paying for before signing. The estimate becomes the contract, and the final invoice reflects it — no lump-sum numbers we can pad quietly.
Our TX crews operate from locally based dispatch — not a regional hub routing jobs to whoever's available statewide. That means faster arrival windows, familiarity with local building departments, and crews who know Amherst's specific code requirements.
An unlicensed contractor on your property creates liability exposure for you personally. License verification before signing eliminates the most common contractor fraud scenario in the Amherst, TX market.
We also deliver a complete close-out package: permit records, manufacturer warranty registrations, and post-project photos organized by elevation. That file is useful for insurance renewals, property sales, and HOA records long after the project ends.
A crew that leaves a clean site every evening is a crew that respects the property they're working on. We treat cleanup as part of the daily schedule, not a last-day obligation.
The lead installer contacts you each morning to confirm the day's scope and each afternoon to report what was completed. If the project uncovers unexpected conditions — the sheathing damage that shows up during tear-off — you hear about it same-day with photos and a written change order, before we touch anything additional.
A predictable process consistently produces better results than a flexible one. Here's exactly what to expect.
Our Amherst, TX dispatch team takes your call and books a free on-site assessment within 24–48 hours. We arrive with measuring tools and a moisture meter, document all wall planes and existing substrate conditions, and identify any issues before quoting.
Delivered within 24 hours of the site visit. Every component — panels, trim, housewrap, fasteners, labor, permit fee — listed separately. We bring material samples to the estimate meeting and walk through the product trade-offs relevant to your Amherst, TX property.
Material is ordered against the confirmed schedule. We don't stage material before it's needed and we don't start jobs with missing material. Your crew arrives on day one with everything they need.
Morning update from the lead installer confirming the day's scope. Afternoon update reporting what was completed. Unexpected substrate conditions documented same-day with photos and a written change order — never added to the invoice without prior approval.
Close-out package delivered: permit records, manufacturer warranty registrations in your name, post-project photos by elevation, and our signed workmanship warranty document. Everything in one organized file.
Full replacement, line-item estimate, project finished on schedule, and a close-out package with every warranty document organized before I signed off on final payment. This is what a professional siding project actually looks like.
The insurance documentation package they produced — panel-by-panel photos, written damage scope by elevation — got our claim approved at full replacement on first review. The adjuster told us it was the most detailed storm documentation he'd seen that year.
Pre-purchase inspection on a property we were evaluating found sheathing moisture on two elevations the general home inspector had completely missed. Used the written report to negotiate a $12,000 seller credit. The inspection paid for itself about 40 times over.
I verified the license number in the TX database before signing. Current, properly classified, no history. That two-minute check was the most useful thing I did in the entire contractor selection process.
Fiber cement installation — the back-priming at every field cut, the fastener schedule documentation, the manufacturer warranty registration. I've seen fiber cement installed by other contractors. I know what the correct process looks like. Forge Siding followed every step of it.
Site was clean every evening — tarps on the landscaping, fasteners swept, no debris left overnight. On the last day of the project, the yard looked better than when they'd arrived. That's a detail that matters.
Proximity matters for response time and for practical accountability. Our Amherst crews work in Amherst, TX communities year-round, building the inspector relationships, material supplier reliability, and local code familiarity that produce better project outcomes than out-of-market operations working from a generic spec sheet.
Currently active in: 79312 and surrounding areas