Forge Siding delivers professional Siding across Lewisville, TX with locally based crews who understand Lewisville's specific climate conditions, permit requirements, and building codes. Not a franchise call center routing jobs to whoever's free — a licensed contractor with written credentials and a documented track record.

Forge Siding has been delivering Siding across Lewisville, TX for over fifteen years. Our lead installers hold manufacturer certifications on every cladding system we install — fiber cement, vinyl, engineered wood, steel — and the same crew that estimates your project executes it. We don't sub out the technical work.
We work across the full project range: single-panel storm repairs, complete whole-home re-siding, new construction cladding alongside general contractors, and commercial multi-family projects for property managers who need consistent quality and documentation across multiple buildings.
We've completed projects in every climate zone Lewisville, TX presents — high-humidity coastal exposures, high-altitude freeze-thaw cycling, urban heat island conditions. That geographic breadth translates to practical knowledge about product selection and installation specification that out-of-market contractors working from a generic spec sheet simply don't have.

Most siding failures start as small, quiet problems. Catching them before they reach your wall cavity changes the repair scope dramatically — and the cost even more so.
Any crack through the panel face is an active moisture entry point. Window corners and butt joints are the highest-risk locations — and the easiest to overlook until they've allowed a full season of water infiltration.
Drywall staining, soft spots when you press near exterior walls, or a persistent musty odor in exterior-adjacent rooms are downstream indicators. The sheathing has usually been wet for weeks before these symptoms appear.
Buckled vinyl means panels were installed too tight for the thermal range — no expansion room for seasonal movement. The deformation grows with each heat cycle and eventually opens the panel lock, creating wind and water entry points.
On fiber cement specifically, field cuts that weren't back-primed at installation are the entry point. The paint fails at cut edges first and the pattern makes the cause obvious to anyone who's diagnosed it before.
Fastener specification is the most commonly skipped installation requirement. We've documented hundreds of Lewisville, TX properties where the original installer used bright nails on fiber cement, voiding the material warranty before the first winter.
Wall air leakage through siding failures can account for 10–20% of annual HVAC energy consumption. Addressing the envelope often produces measurable utility savings alongside the repair value.
Our Lewisville, TX team handles the full spectrum of residential and commercial cladding work from single-panel storm repairs to complete building envelope re-siding on large multi-family properties.
Installation quality is the variable that separates a 15-year siding job from a 35-year one. The correct expansion gap for your TX climate, the proper back-priming of fiber cement field cuts, the housewrap integration at rough openings — these details determine long-term performance and they aren't optional on our projects.
For full replacement projects, our tear-off process includes substrate inspection with a calibrated moisture meter on every exposed wall section. Sheathing damage found during demo is documented with photos and priced in a written change order before any additional work proceeds — not discovered on the final invoice.

Siding repair in Lewisville, TX covers a range that extends well beyond swapping a cracked panel: hail and wind damage after storms, impact holes from debris or vehicle contact, failed caulk joints at penetrations allowing water infiltration, loose or blown-off panels, and moisture-infiltrated substrate that requires sheathing repair before new cladding can go on. Our Lewisville, TX repair crews carry common panel stock, a moisture meter, and caulk probe tools on every service truck — so assessment and often same-day repair happen in a single visit.
Emergency dispatch for genuine siding emergencies — missing panels with rain incoming, active moisture entry into a wall cavity, structural damage — is available around the clock. A live dispatcher answers, not an answering queue. We triage by exposure severity and send a crew based on actual risk.

Each cladding material has distinct installation requirements that determine whether it performs for 10 years or 40. Our Lewisville, TX crews hold certifications specific to the products they install — not one generic approach applied to every material. Fiber cement installation requires back-priming at every field cut, hot-dipped galvanized or stainless fasteners, documented fastener schedules per the manufacturer guide, and silica dust controls during cutting operations. Vinyl installation requires expansion gaps calibrated to the local temperature range in TX. Wood siding requires moisture content verification at delivery, species-appropriate nailing patterns, and end-grain sealing at every butt joint. We address each of these requirements as non-negotiable installation practice.
For commercial and multi-family projects in TX, our operation extends to HOA communities, property management portfolios, and new construction cladding for GCs who need a reliable siding subcontractor with documented quality control. Standardized per-building documentation and a single project point of contact make multi-unit work manageable for property managers.

Siding doesn't end at the wall panels. Soffit, fascia, corner posts, J-channel, window trim, door trim, and all penetration accessories are part of the building envelope — and failing trim components are among the most common moisture entry points we encounter during inspection and repair calls. Our Lewisville, TX crews handle the complete trim system as standard scope on every installation project.

A professional siding inspection before buying or selling a Lewisville, TX property gives you panel-level condition documentation that general home inspectors don't produce. We assess fastener schedules, test caulk integrity at penetrations, probe sheathing moisture with calibrated meters, and deliver a priority-ranked written report with photo documentation and rough repair cost ranges. Pre-purchase inspections have identified sheathing moisture on properties where the general inspection report said the siding was "in acceptable condition."

Commercial siding in TX operates on different requirements than residential: higher fastener schedules for wind-load compliance, special inspection documentation in applicable jurisdictions, coordinated scheduling for occupied buildings, and standardized documentation for HOA board records and reserve fund planning. Our commercial crews are familiar with the permitting landscape in TX and have completed projects ranging from small townhome communities to larger multi-family re-siding contracts.

These aren't aspirational claims. They're the operational standards our Lewisville, TX clients reference when they send us referrals. Each one is documented and verifiable.
Materials, labor, permit fees, and disposal listed separately on every estimate. You know exactly what you're paying for before signing. The estimate becomes the contract, and the final invoice reflects it — no lump-sum numbers we can pad quietly.
We don't schedule jobs we can't start within a reasonable window. Current backlog means a delay? We tell you upfront with realistic dates, not optimistic ones designed to close the sale.
Our TX contractor license number is provided at first contact. Two minutes in the state database tells you our status, our classification, and our disciplinary history. GL and workers' comp certificates are available before work starts — not expired documents or certificates for a different company name.
Every completed project closes with a signed warranty document: coverage period, covered defects, and the resolution process — all specified in writing. Manufacturer warranties registered in your name at project completion. Not a verbal promise; a document you can file, reference, and enforce.
A crew that leaves a clean site every evening is a crew that respects the property they're working on. We treat cleanup as part of the daily schedule, not a last-day obligation.
You don't have to call us to find out where your project stands. We tell you, every day, in writing.
The same documented process governs every project we take in Lewisville, TX. No mystery, no moving goalposts — you know what's happening at every stage.
Our Lewisville, TX dispatch team takes your call and books a free on-site assessment within 24–48 hours. We arrive with measuring tools and a moisture meter, document all wall planes and existing substrate conditions, and identify any issues before quoting.
Delivered within 24 hours of the site visit. Every component — panels, trim, housewrap, fasteners, labor, permit fee — listed separately. We bring material samples to the estimate meeting and walk through the product trade-offs relevant to your Lewisville, TX property.
Material is ordered against the confirmed schedule. We don't stage material before it's needed and we don't start jobs with missing material. Your crew arrives on day one with everything they need.
Morning update from the lead installer confirming the day's scope. Afternoon update reporting what was completed. Unexpected substrate conditions documented same-day with photos and a written change order — never added to the invoice without prior approval.
We walk every elevation with you at project completion. Every scope item verified complete. If anything isn't right, we note it and fix it before considering the project closed. Final payment collected after the walkthrough sign-off — not before.
The moisture meter reading at the estimate visit — before we'd agreed to anything — flagged elevated sheathing moisture behind our north wall. That diagnostic step upfront told me immediately what kind of contractor I was dealing with. The rest of the project matched that first impression exactly.
The insurance documentation package they produced — panel-by-panel photos, written damage scope by elevation — got our claim approved at full replacement on first review. The adjuster told us it was the most detailed storm documentation he'd seen that year.
Pre-purchase inspection on a property we were evaluating found sheathing moisture on two elevations the general home inspector had completely missed. Used the written report to negotiate a $12,000 seller credit. The inspection paid for itself about 40 times over.
They found rotted sheathing on the west wall during tear-off. Called me within the hour, showed me the photos, issued a change order before doing anything. That's the process working exactly as it should — and it's shockingly rare in my experience with contractors.
The daily morning and afternoon updates from the lead installer were something I hadn't expected. I always knew exactly where the project stood. When the permit inspection happened, I heard about it the same day it passed.
Three bids — two lump sums and one line-item breakdown from Forge Siding. The line-item document made comparison possible in a way the other two bids didn't. When the choice becomes that clear, the decision is easy.
Forge Siding provides residential and commercial Siding across the full Lewisville, TX service area from our locally based Lewisville dispatch team. We're familiar with local building codes, permit requirements, and contractor licensing standards throughout TX — no learning curve on your project, no out-of-area crew navigating unfamiliar inspectors and building departments for the first time.
Currently active in: 75067 75065 75056 75057 75077 75029 and surrounding areas