When your siding fails, it doesn't fail quietly. Moisture gets into sheathing, energy costs climb, and the interior damage that follows is always more expensive than the exterior repair that would have stopped it. Forge Siding puts licensed, manufacturer-certified crews on your Woodinville property — crews who diagnose the actual problem, price it in writing, and fix it once.

Forge Siding has been delivering Siding across Woodinville, WA for over fifteen years. Our lead installers hold manufacturer certifications on every cladding system we install — fiber cement, vinyl, engineered wood, steel — and the same crew that estimates your project executes it. We don't sub out the technical work.
Our WA operation is licensed, bonded, and insured — GL and workers' comp both current, certificates available before any project starts. Not because it's optional, but because a property owner deserves protection when they invite a crew onto their building.
We've completed projects in every climate zone Woodinville, WA presents — high-humidity coastal exposures, high-altitude freeze-thaw cycling, urban heat island conditions. That geographic breadth translates to practical knowledge about product selection and installation specification that out-of-market contractors working from a generic spec sheet simply don't have.

Most siding failures start as small, quiet problems. Catching them before they reach your wall cavity changes the repair scope dramatically — and the cost even more so.
Any crack through the panel face is an active moisture entry point. Window corners and butt joints are the highest-risk locations — and the easiest to overlook until they've allowed a full season of water infiltration.
Interior moisture near windows is frequently misdiagnosed as a window problem. Failed flashing or caulk at the rough opening — a siding-system issue — is the actual source in the majority of cases we diagnose in WA.
Buckled vinyl means panels were installed too tight for the thermal range — no expansion room for seasonal movement. The deformation grows with each heat cycle and eventually opens the panel lock, creating wind and water entry points.
Exterior paint failing within two to four years of application on wood or fiber cement is almost always a back-priming failure — moisture migrates through the panel from behind and pushes the front paint off. Re-painting without addressing this repeats the cycle.
Dark streaking from nailhead locations on vinyl or fiber cement means non-galvanized fasteners are corroding. As the fastener degrades, its holding strength decreases — a panel secured by a corroded nail is a panel waiting to separate in a windstorm.
Wall air leakage through siding failures can account for 10–20% of annual HVAC energy consumption. Addressing the envelope often produces measurable utility savings alongside the repair value.
Every service below is performed by our own licensed crew — not passed to a subcontractor network we don't control. We carry the manufacturer certifications, the diagnostic tools, and the installation experience for every scope we quote.
New siding installation covers the complete scope: housewrap, flashing at all penetrations, panel installation per manufacturer specification, and finishing trim at corners, windows, doors, and the roofline. We work on new construction alongside general contractors and handle full tear-off replacements on existing Woodinville, WA homes and commercial properties. Our crews are certified on vinyl, fiber cement, engineered wood, and steel panel systems — with the documentation to keep every material warranty in force.
We also handle the complete trim system: corner posts, J-channel, soffit panels, fascia wrap, and all penetration accessories. Not as an optional add-on — as part of every installation scope, because a new siding system that terminates into failing trim defeats the purpose of the project.

Root cause diagnosis before any repair work is our standing process. A cracked panel that gets swapped without investigating the housewrap beneath, a caulk joint that gets re-sealed without checking sheathing moisture — these are surface patches over active problems. We find the cause first, quote the actual fix in writing, and then execute.
For insurance-related damage, we produce a panel-level photo documentation package — close-range images by elevation, written damage scope, and material specifications formatted for adjuster review. After the initial adjuster estimate comes in lower than the actual scope, our documentation has supported successful appeals on a significant number of Woodinville, WA claims. That documentation service is included in every storm inspection at no additional charge.

Manufacturer certification matters for one concrete reason: it's the difference between a material warranty that's in force and one that's already voided before the project is complete. Our James Hardie Preferred Contractor status, for example, means the 30-year material warranty on every fiber cement project we complete is fully registered in the client's name at project close.
Beyond installation, we perform professional siding inspections — pre-purchase assessments for buyers, post-storm condition reports for insurance claims, and annual maintenance inspections for property owners who want to catch caulk failures and minor fastener movement before they become moisture damage. These inspections use calibrated pin-type and non-invasive capacitance meters for moisture assessment — tools a general home inspector doesn't carry. The written report you receive ranks deficiencies by priority and includes rough cost ranges for every item.

Vinyl soffit and fascia wrap, HardieTrim boards, aluminum-capped fascia, and fiber cement trim boards are all within our scope. On replacement projects, we replace trim components that are damaged or compromised regardless of the primary panel material — because leaving failing trim behind a new siding installation creates the exact moisture entry point the new siding was supposed to eliminate.

Post-storm inspections document hail and wind damage at panel face level — the close-range evidence that insurance adjusters need for full-scope claim approvals. We've helped Woodinville, WA property owners recover claim settlements that significantly exceeded initial adjuster estimates by providing specific, photo-verifiable panel-count documentation rather than general damage descriptions.

Commercial siding in WA operates on different requirements than residential: higher fastener schedules for wind-load compliance, special inspection documentation in applicable jurisdictions, coordinated scheduling for occupied buildings, and standardized documentation for HOA board records and reserve fund planning. Our commercial crews are familiar with the permitting landscape in WA and have completed projects ranging from small townhome communities to larger multi-family re-siding contracts.

These aren't aspirational claims. They're the operational standards our Woodinville, WA clients reference when they send us referrals. Each one is documented and verifiable.
Materials, labor, permit fees, and disposal listed separately on every estimate. You know exactly what you're paying for before signing. The estimate becomes the contract, and the final invoice reflects it — no lump-sum numbers we can pad quietly.
Our WA crews operate from locally based dispatch — not a regional hub routing jobs to whoever's available statewide. That means faster arrival windows, familiarity with local building departments, and crews who know Woodinville's specific code requirements.
An unlicensed contractor on your property creates liability exposure for you personally. License verification before signing eliminates the most common contractor fraud scenario in the Woodinville, WA market.
We also deliver a complete close-out package: permit records, manufacturer warranty registrations, and post-project photos organized by elevation. That file is useful for insurance renewals, property sales, and HOA records long after the project ends.
A crew that leaves a clean site every evening is a crew that respects the property they're working on. We treat cleanup as part of the daily schedule, not a last-day obligation.
You don't have to call us to find out where your project stands. We tell you, every day, in writing.
The same documented process governs every project we take in Woodinville, WA. No mystery, no moving goalposts — you know what's happening at every stage.
Our Woodinville, WA dispatch team takes your call and books a free on-site assessment within 24–48 hours. We arrive with measuring tools and a moisture meter, document all wall planes and existing substrate conditions, and identify any issues before quoting.
The estimate is a document, not a handshake. It becomes the contract, and every line item is visible before you sign. No lump-sum number to parse after the fact.
Where permits are required in WA, we handle the application, filing fee, and inspection scheduling as part of standard scope. Your confirmed start date is in writing and the crew assignment is confirmed before materials are ordered.
Morning update from the lead installer confirming the day's scope. Afternoon update reporting what was completed. Unexpected substrate conditions documented same-day with photos and a written change order — never added to the invoice without prior approval.
Close-out package delivered: permit records, manufacturer warranty registrations in your name, post-project photos by elevation, and our signed workmanship warranty document. Everything in one organized file.
Full replacement, line-item estimate, project finished on schedule, and a close-out package with every warranty document organized before I signed off on final payment. This is what a professional siding project actually looks like.
The insurance documentation package they produced — panel-by-panel photos, written damage scope by elevation — got our claim approved at full replacement on first review. The adjuster told us it was the most detailed storm documentation he'd seen that year.
We manage a 34-unit townhome community. The per-building documentation, the building-by-building scheduling, the HOA board close-out package — these are things I'd been trying to get from contractors for years and never received until Forge Siding.
I verified the license number in the WA database before signing. Current, properly classified, no history. That two-minute check was the most useful thing I did in the entire contractor selection process.
The daily morning and afternoon updates from the lead installer were something I hadn't expected. I always knew exactly where the project stood. When the permit inspection happened, I heard about it the same day it passed.
Site was clean every evening — tarps on the landscaping, fasteners swept, no debris left overnight. On the last day of the project, the yard looked better than when they'd arrived. That's a detail that matters.
Forge Siding provides residential and commercial Siding across the full Woodinville, WA service area from our locally based Woodinville dispatch team. We're familiar with local building codes, permit requirements, and contractor licensing standards throughout WA — no learning curve on your project, no out-of-area crew navigating unfamiliar inspectors and building departments for the first time.
Serving zip codes: 98072 98077