When your siding fails, it doesn't fail quietly. Moisture gets into sheathing, energy costs climb, and the interior damage that follows is always more expensive than the exterior repair that would have stopped it. Forge Siding puts licensed, manufacturer-certified crews on your Berlin property — crews who diagnose the actual problem, price it in writing, and fix it once.

What makes our Berlin operation different isn't a slogan. It's the fact that every estimate we write is line-item detailed, every project has a named lead installer accountable for the outcome, and every completed job closes with a written workmanship warranty you can actually enforce.
Our CT operation is licensed, bonded, and insured — GL and workers' comp both current, certificates available before any project starts. Not because it's optional, but because a property owner deserves protection when they invite a crew onto their building.
We've completed projects in every climate zone Berlin, CT presents — high-humidity coastal exposures, high-altitude freeze-thaw cycling, urban heat island conditions. That geographic breadth translates to practical knowledge about product selection and installation specification that out-of-market contractors working from a generic spec sheet simply don't have.

Most siding failures start as small, quiet problems. Catching them before they reach your wall cavity changes the repair scope dramatically — and the cost even more so.
Any crack through the panel face is an active moisture entry point. Window corners and butt joints are the highest-risk locations — and the easiest to overlook until they've allowed a full season of water infiltration.
Drywall staining, soft spots when you press near exterior walls, or a persistent musty odor in exterior-adjacent rooms are downstream indicators. The sheathing has usually been wet for weeks before these symptoms appear.
Buckled vinyl means panels were installed too tight for the thermal range — no expansion room for seasonal movement. The deformation grows with each heat cycle and eventually opens the panel lock, creating wind and water entry points.
On fiber cement specifically, field cuts that weren't back-primed at installation are the entry point. The paint fails at cut edges first and the pattern makes the cause obvious to anyone who's diagnosed it before.
Dark streaking from nailhead locations on vinyl or fiber cement means non-galvanized fasteners are corroding. As the fastener degrades, its holding strength decreases — a panel secured by a corroded nail is a panel waiting to separate in a windstorm.
A compromised siding system — failed housewrap, open panel joints, missed penetration caulk — creates air infiltration that significantly increases HVAC load. If your heating or cooling costs have climbed without obvious explanation, the building envelope is a legitimate first suspect.
Every service below is performed by our own licensed crew — not passed to a subcontractor network we don't control. We carry the manufacturer certifications, the diagnostic tools, and the installation experience for every scope we quote.
Installation quality is the variable that separates a 15-year siding job from a 35-year one. The correct expansion gap for your CT climate, the proper back-priming of fiber cement field cuts, the housewrap integration at rough openings — these details determine long-term performance and they aren't optional on our projects.
We also handle the complete trim system: corner posts, J-channel, soffit panels, fascia wrap, and all penetration accessories. Not as an optional add-on — as part of every installation scope, because a new siding system that terminates into failing trim defeats the purpose of the project.

Root cause diagnosis before any repair work is our standing process. A cracked panel that gets swapped without investigating the housewrap beneath, a caulk joint that gets re-sealed without checking sheathing moisture — these are surface patches over active problems. We find the cause first, quote the actual fix in writing, and then execute.
For insurance-related damage, we produce a panel-level photo documentation package — close-range images by elevation, written damage scope, and material specifications formatted for adjuster review. After the initial adjuster estimate comes in lower than the actual scope, our documentation has supported successful appeals on a significant number of Berlin, CT claims. That documentation service is included in every storm inspection at no additional charge.

Manufacturer certification matters for one concrete reason: it's the difference between a material warranty that's in force and one that's already voided before the project is complete. Our James Hardie Preferred Contractor status, for example, means the 30-year material warranty on every fiber cement project we complete is fully registered in the client's name at project close.
Beyond installation, we perform professional siding inspections — pre-purchase assessments for buyers, post-storm condition reports for insurance claims, and annual maintenance inspections for property owners who want to catch caulk failures and minor fastener movement before they become moisture damage. These inspections use calibrated pin-type and non-invasive capacitance meters for moisture assessment — tools a general home inspector doesn't carry. The written report you receive ranks deficiencies by priority and includes rough cost ranges for every item.

Vinyl soffit and fascia wrap, HardieTrim boards, aluminum-capped fascia, and fiber cement trim boards are all within our scope. On replacement projects, we replace trim components that are damaged or compromised regardless of the primary panel material — because leaving failing trim behind a new siding installation creates the exact moisture entry point the new siding was supposed to eliminate.

A professional siding inspection before buying or selling a Berlin, CT property gives you panel-level condition documentation that general home inspectors don't produce. We assess fastener schedules, test caulk integrity at penetrations, probe sheathing moisture with calibrated meters, and deliver a priority-ranked written report with photo documentation and rough repair cost ranges. Pre-purchase inspections have identified sheathing moisture on properties where the general inspection report said the siding was "in acceptable condition."

Commercial siding in CT operates on different requirements than residential: higher fastener schedules for wind-load compliance, special inspection documentation in applicable jurisdictions, coordinated scheduling for occupied buildings, and standardized documentation for HOA board records and reserve fund planning. Our commercial crews are familiar with the permitting landscape in CT and have completed projects ranging from small townhome communities to larger multi-family re-siding contracts.

There are plenty of siding contractors in CT. Here's what the ones worth hiring actually do differently.
Materials, labor, permit fees, and disposal listed separately on every estimate. You know exactly what you're paying for before signing. The estimate becomes the contract, and the final invoice reflects it — no lump-sum numbers we can pad quietly.
Our CT crews operate from locally based dispatch — not a regional hub routing jobs to whoever's available statewide. That means faster arrival windows, familiarity with local building departments, and crews who know Berlin's specific code requirements.
An unlicensed contractor on your property creates liability exposure for you personally. License verification before signing eliminates the most common contractor fraud scenario in the Berlin, CT market.
We also deliver a complete close-out package: permit records, manufacturer warranty registrations, and post-project photos organized by elevation. That file is useful for insurance renewals, property sales, and HOA records long after the project ends.
A crew that leaves a clean site every evening is a crew that respects the property they're working on. We treat cleanup as part of the daily schedule, not a last-day obligation.
The lead installer contacts you each morning to confirm the day's scope and each afternoon to report what was completed. If the project uncovers unexpected conditions — the sheathing damage that shows up during tear-off — you hear about it same-day with photos and a written change order, before we touch anything additional.
The same documented process governs every project we take in Berlin, CT. No mystery, no moving goalposts — you know what's happening at every stage.
You get a real conversation with a dispatcher who knows the product — not a scheduling app that drops your request into a queue. The site assessment is diagnostic, not just a measuring visit.
Delivered within 24 hours of the site visit. Every component — panels, trim, housewrap, fasteners, labor, permit fee — listed separately. We bring material samples to the estimate meeting and walk through the product trade-offs relevant to your Berlin, CT property.
Material is ordered against the confirmed schedule. We don't stage material before it's needed and we don't start jobs with missing material. Your crew arrives on day one with everything they need.
Morning update from the lead installer confirming the day's scope. Afternoon update reporting what was completed. Unexpected substrate conditions documented same-day with photos and a written change order — never added to the invoice without prior approval.
We walk every elevation with you at project completion. Every scope item verified complete. If anything isn't right, we note it and fix it before considering the project closed. Final payment collected after the walkthrough sign-off — not before.
The moisture meter reading at the estimate visit — before we'd agreed to anything — flagged elevated sheathing moisture behind our north wall. That diagnostic step upfront told me immediately what kind of contractor I was dealing with. The rest of the project matched that first impression exactly.
The insurance documentation package they produced — panel-by-panel photos, written damage scope by elevation — got our claim approved at full replacement on first review. The adjuster told us it was the most detailed storm documentation he'd seen that year.
Pre-purchase inspection on a property we were evaluating found sheathing moisture on two elevations the general home inspector had completely missed. Used the written report to negotiate a $12,000 seller credit. The inspection paid for itself about 40 times over.
I verified the license number in the CT database before signing. Current, properly classified, no history. That two-minute check was the most useful thing I did in the entire contractor selection process.
The daily morning and afternoon updates from the lead installer were something I hadn't expected. I always knew exactly where the project stood. When the permit inspection happened, I heard about it the same day it passed.
Three bids — two lump sums and one line-item breakdown from Forge Siding. The line-item document made comparison possible in a way the other two bids didn't. When the choice becomes that clear, the decision is easy.
Forge Siding provides residential and commercial Siding across the full Berlin, CT service area from our locally based Berlin dispatch team. We're familiar with local building codes, permit requirements, and contractor licensing standards throughout CT — no learning curve on your project, no out-of-area crew navigating unfamiliar inspectors and building departments for the first time.
Serving zip codes: 6037